Yeoman and servicing Manual de usuario

Yeoman CLHigh Output Boiler StovesInstructions for Use, Installation & ServicingFor use in GB & IE (Great Britain & Republic of Ireland).P

1012-+Control KnobSetting Indicator5.23 The exact setting of the thermostat and the Manual Air Controls may need slight adjustment by trial and error

11User Instructions6.5 Fit the plug supplied into the hole where the riddling mechanism is normally located and secure with bolt and clamp (also s

128.4 Place the ash into an Ash Caddy (Part No. 4227) or other suitable container. 8.5 Check and remove ash as often as required when burning solid

13Care & Maintenance13. Chimney Sweeping13.1 To maintain safe and efficient use of the appliance, the chimney/flue must be inspected and swept at

14TroubleshootingSymptom Cause SolutionOPERATIONDifficulty starting the fire andkeeping it burning wellLow flue draught Consult your installerWet wood

15TroubleshootingSymptom Cause SolutionTHE APPLIANCERapid creosote build-up in the chimney Wet wood (over 20% moisture)Use dry seasoned wood (less tha

16Installation ChecklistPlease NoteThis section is intended to give an overview of the product performance and essential information required for inst

17Installation Checklist2. Essential InformationGENERALModel:Yeoman CL8Yeoman CL8Nominal Heat Output to RoomWood kW 6.4Solid Fuel kW6.4Nominal Heat Ou

18Installation Checklist5. ClearancesIMPORTANT: INSTALLATION MUST COMPLY WITH CURRENT BUILDING REGULATIONSENSURE THAT SUFFICIENT CLEARANCES ARE PROVID

19Installation ChecklistNon-Combustible Materials5.2 All appliances will require some clearance between them and any non-combustible materials to all

2Covering the following models:YM-CL8HBMF1 Yeoman CL - High Output Boiler StovesContentsAppliance Commissioning Checklist ...3User

201. General1.1 To make the installation of the appliance easier it is best to remove the internal components before fitting into the builders openin

21 Note: When installed correctly the front of the baffle fits over the supports on the inside of the firebox and the back fits over the Secondary Ai

226. Removal of the Riddling Mechanism The riddling mechanism can be removed for cleaning to maintain good working condition.To remove the riddling m

23Pre-Installation Instructions7. Removal of the Cast Plinth7.1 The Cast Plinth can be removed to aid in the installation or as part of the routine m

24Installation Instructions1. Installing the ApplianceEach installation is unique to the property so it is not possible to give details to suit every

25Installation Instructions1.8 Place the cast top plate feet down on top of the appliance.1.9 Ensure the cast top is flush with the front and sides

26 The Flue must be installed in accordance with manufacturers instructions.Seal Collar with Fire CementSelf tapping screwTeeSize Part No.6" 461

274. Open Vent & Cold Feed System4.1 This system must be fitted with a minimum of 22mm diameter open vent discharging into a heat resisting feed

28Installation Instructions11. Sealed (Pressurized) System11.1 Do not fit this appliance to sealed or pressurised systems or an unvented hot water cy

29HEATING SYSTEM CONTROLSCONTROLS GENERAL1.1 The controls fitted to the system will provide two functions: — To control the comfort level in the hou

3Retailer appliance was purchased from:Name:Address:Telephone number:Essential information - MUST be completed:Date Installed:Model Description:Serial

30Commissioning1. Commissioning1.1 To commission: — Replace the internal components. — Check the door alignment and catch operation, adjust if

31Certificate Of Compliance Upon completing the installation, the form below must be filled in by your installer to comply with the requirements of H

32Maintenance & ServicingFor a complete list of spare parts and accessories contact your Yeoman or call 01392 4740111. Annual Service1.1 Before t

333. Removing the Woodburning Tray (if fitted) To maintain safe use of the appliance the Woodburning tray should be removed and cleaned regularly .3.

34Maintenance & Servicing4.8 Fix glass sealing rope (B) to the matt black side of the top face, see Diagram 4. .Glass rope sealBBlack face44..9

357. Adjusting the Door Catch7.1 To adjust the door catch: —Open the door to gain access to the catch.7.2 Use a 13mm A/F spanner to loosen the half

36Technical AppendixLegal RequirementsBefore installation and/or use of this appliance please read these instructions carefully to ensure that all req

37Technical Appendix - Flues1. Flue or Chimney2.1 The flue or chimney system must be in good condition. It must be inspected by a competent person a

382. Ventilation2.1 Many older buildings are sufficiently ventilated by natural leakage of air to provide suitable air supply for an appliance of 5kW

394. Fitting Appliances On A Boat4.1 If an appliance is to be fitted in a boat it must be done in accordance with the latest edition of BS 8511 (Code

4Welcome Congratulations on purchasing your Yeoman CL Boiler, if installed correctly Yeoman hope it will give you many years of warmth and pleasure f

40Ref. Description1CAST DOOR2DOOR HANDLE ASSEMBLY3WAVE SPRING 4SPRING 6.1MM O/D X 0.61MM DIAMETER WIRE X 22.2MM LONG5TORSION SPRING6DOOR HANDLE CAM7HI

41Due to continual technical improvements please check online at www.yeomanstoves.co.uk for the most up to date parts lists.Basic Spare PartsRIDDLING

421STSERVICEDate of Service:...Next Service Due:...

Stovax Ltd, Falcon Road, Sowton Industrial Estate, Exeter, Devon, England EX2 7LFTel: (01392) 474011 Fax: (01392) 219932 E-mail: [email protected]

5Getting StartedAIR CONTROLSTriple Air Systems Several Yeoman appliances have triple air systems providing cleaner burning, and greater efficiency an

61.19 It is also recommended to fit a low limit thermostat on the centralheatingreturnsetat45˚C.Thisthermostatwillturnthepumpoffifther

7 Poor quality timber: — Causes low combustion efficiency — Produces harmful condensation — Reduces effectiveness of the airwash and life of the

8Base ofbaffleLog Guard8 —Close the door. Do not run with the door slightly open except for initial lighting as this could cause over-firing and dama

9 Operate the follow controls manually:Secondary Air Control Always have the Secondary Air Control shut when burning solid fuel to ensure the maximu